|
|
|
|
|
|
|
|
We designed our shift knobs to mimic the ones used in the C5R racing
Corvettes that run in LeMans and Sebring. Our knobs are threaded specific
to each application.
The Pantera shift knobs are 3 1/4" tall but only half an inch sits above the
shift stock (see figure below.) This means that your hand position will be
considerably lower, essentially turning your OEM shifter into a short shifter
for quicker shifts and better looks!
- Vertical design leads to solid shifts, gives added leverage and keeps your hand in a
very natural position.
- Machine lathed out of Delrin and hand finished to
be smooth to the touch.
- Delrin never gets too hot in the summer or too cold in the winter.
- Delrin acts as a vibration dampener and transfers less noise through the shifter.
|
| |
|
 |
|
|
|
|
Shown with our Shift Boot and Shift Pattern Plate. |
|
 |
|
|
|
|
|
|
Want to convert to Group4 style tail lights? Auger Resources has teamed up
with Pantera Electronics
to bring you a stylish alternative to hard to find
Group4 tail lights. Besides being super cool, high tech, and ultra bright, the
LED's offer these advantages:
- Reverse gear strobes the turn signal LED arrays for added safety.
(See it on YouTube.)
- LED's illuminate 0.20 seconds faster than incandescent bulbs
(equates to 19 feet on the freeway.)
- No filament to burn-out, LED life is a minimum of 50,000 hours.
- 60% lower power requirement, extends headlight switch life.
- Constant brightness, even at idle engine speed.
- Simple wiring, matching color wires to the original harness.
- Modern appearance without distorting the original design.
- New! Clear lens option!
LEDs and buckets made proudly in the USA!
|
|
Our complete LED Tail Lights include the LED bucket assemblies and
brand new Carello Style lenses. Everything comes fully assembled so all you
need to do is bolt them to your car and connect the wires. Take a look at our
on-line installation instructions for details.
Scroll down to see the LED Taillights installed.
|
 Colored Lenses |
Currently we only have clear lenses in stock. |
 Clear Lenses |
| |
If you already have lenses, our "buckets only" option is for you. Our aluminum
buckets come pre-assembled, complete with new rubber gaskets, stainless
hardware, LEDs and connectors. Please specify whether you have Altissimo
or Carello style lenses (you can find the name directly on the lenses.) Installation is easy - see our
on-line installation instructions for details.
|
 |
|
|
| |
If you have LED's in both the front and rear lights, you'll need an electronic
flasher. We carry Pantera Electronics' flasher. It plugs straight in and has an
electronic speaker so you can still hear the flashers.
|
 |
|
|
| |
|
|
|
|
|
|
|
|
| |
Need new gaskets for your Group4 style tail light lenses?
We have them! These are brand new gaskets made of the highest quality material right here
in the USA.
The gaskets are notched where they line up with the light dividers and are
marked for the left and right sides of the car.
|
 |
|
|
|
 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Panteras had the shift pattern labeled on the shift gate but, over the years, many gates have been
removed, changed or maybe even covered with one of our shift boots! With the unique gear layout, a
constant reminder is needed and our aluminum shift plates are the solution.
- Shift pattern is clearly anodized in black.
- Thick aluminum plate
- Backed with heavy duty, high temp 3M adhesive.
- Simply clean the mounting surface, then peel and stick.
|
| |
|
|
|
|
|
|
|
|
Shown with our Shift Boot and Shift Knob. |
|
 |
|
|
|
|
